Eprom Cartridge Rev 1.5

Rookie (17)

05-10-2021, 18:11

Hi guys,

I have built this Eprom Cart for MSX based on project files here : Eprom Cartridge rev 1.5
I burned a 27C256 with the MSXDiag (I would like also to use this cart with the RamTest) but when I pop this into the cartridge slot of my HX-10 all I get is a black screen and a humming noise. oO
My question is fairly simple : does anyone had a chance to built this cart and make it working? There is no documentation over the net on how to use it and especially how to set the jumpers on top.
I have watched a video with this cart working on an MSX with all jumpers left opened.
Any help would be appreciated :D
[img][/img]

ログイン/登録して投稿

By sdsnatcher73

Prophet (3951)

06-10-2021, 14:02

Weird there is no documentation. For the 32kB ROM you will need CS12 and most likely A14 jumpers selected. The other ones I can’t be sure (probably they say 27plus and 27mimus or ground? (the image is a bit blurry). As you have 256 you will probably need these as opposed to the 1M versions…

By Wierzbowsky

Guardian (3596)

06-10-2021, 18:19

I agree with Peter - you need to set 2 jumpers: CS_12 and P27A14.

The design of this cartridge is pretty chaotic and moreover - potentially dangerous. If all jumpers would have been connected as they should have been by the author's design, then setting 2 jumpers marked as "plus" and "minus" at the same time would have caused a short circuit between power 5V supply and ground.

By repetto74

Rookie (17)

06-10-2021, 16:54

Hi,
Thanks you for your comments on this cart. Posting a better picture of the jumpers section
[img][/img]

By repetto74

Rookie (17)

06-10-2021, 16:56

We have P1MINUS / P1PLUS / P1A15 / CS_1 / CS_2 / CS_12 / RD / P27MINUS / P27A14 / P27PLUS and P27A15

By repetto74

Rookie (17)

06-10-2021, 19:29

I agree with Peter - you need to set 2 jumpers: CS_12 and P27A14.

I have jumpered CS12 and P27A14 but still the same. The MSX won't boot.

I think the electrolytic cap value I am using is wrong. It should be 100uF instead of 47uF so maybe this is the reason why it won't boot.

By Wierzbowsky

Guardian (3596)

06-10-2021, 19:54

This has nothing to do with capacitors. Try to burn a 32kb game ROM (for example Goonies) into the EPROM and see if the game starts. MSXDIAG does a lot of checking before it actually shows anything on the screen, so there may be something that stalls it...

By repetto74

Rookie (17)

06-10-2021, 20:16

Hi Alexey,

Thanks I will try to burn a 32k ROM and check again

By repetto74

Rookie (17)

07-10-2021, 18:06

I have tried to burn Goonies and tested again with no luck and same issue.
This cart PCB looks to be an absolute trash and I will not spend more time on troubleshooting it. I have picked a working PCB cart from the 8BitManshed on Etsy and will be good to go with that one (hopefully).

By Pencioner

Scribe (1562)

07-10-2021, 18:31

8BitManshed, who is also the Banjo guy Ollie - this cart should be working (i bought it and had no problems at all)

By repetto74

Rookie (17)

07-10-2021, 18:56

8BitManshed, who is also the Banjo guy Ollie Wink - this cart should be working (i bought it and had no problems at all)

I am following the guy on his Youtube channel and he does great stuff with arcade PCB repairs and other restorations :-).